Install Software to PC and Open English Version, When we installed LEDEdit 2014 Software, on the desktop we can see following icon:
Please Double-click it, then we into following interface:
Make Effect Program:
We can click the “File (F)” in the English interface, -> “new project” -> it will appear this interface:
Controller Type: you can select the “Controller Type“. If you use the T1000s controller, you must select the “T1000-1903“; If you use the T-4000s controller, you must select the “T4000-1903“; If you use the T-8000 controller, you must select the “T8000-1903“.
Frame Rate: you can select the corresponding number. If you want to the speed faster, you can select large number; If you want to speed slower, you can select small number. We recommend you select the 30.
Save as: this appears to you saved address. You can change the “saved address” by “Browse“.
We use the T1000-1903 Controller for Example. now click “OK”.
Using LEDEdit 2014 Software – Method 1
Then, we need to set the Light Layout. We use the 200 LED ( 4X50) as the Example. We click the “Project Config” -> “start manual layout” -> as follow interface:
In top interface :
Because we use 200 LEDs, then we click, and the mouse “Light Horizontal” click, and do not release the mouse, and dragging to follow:
We can see the Round is horizontal, Then we need to click the “Port” , and click The upper left corner, follow:
Then we need to click the “Line“, and connect the Port with the Round. Follow:
So we made the light layout about 200 LEDs. Then we need to save it.
We click the “File (F)” -> ”save” -> follow:
You can save where you want to save. It will generate the document of “.cxb“. When we saved it, we can close the interface:
Then we back the interface, Then we click “Project Config (C)” -> “import (.cxb)” -> follow:
We need to find the document that we saved the document of “.cxb“, and we need to open it. It will appear the follow interface:
The Green point is we needs.ledpixeltm
Then we click , it have some program-effect, you can select one. So we select the “move right“, it appear follow effect:
Then we must to record the effect, please click the 🔴, to start recording. When we record the effect, we need to click the 🔳 to stop recording.
Export Effect Program which we Made
We here where you want to save. Please click the “Export (O)” -> “export effect(.led)” to follow interface:
The all Steps is over, we can close the follow interface.
We can find the document that we needs. and it need to copy to “SD card“, but the SD card must to format to “FAT Or FAT32” Format.
Using LEDEdit 2014 Software – Method 2
This method is the easiest to use
Click the -> “auto layout“, follow interface:
We only change two parts. the “horizontal Pixel” “50” and the “vertical Pixel” “4“, so the interface was changed to this.
Click the “OK“, The light layout is the same effect.
Using LEDEdit 2014 Software – Method 3
We can use the “Auto CAD” software to set layout.
When we use the “Auto CAD“, we have some request.
The round radius must is 1.0, and the round must be disjoint, and when we use beeline to connect with two rounds, the beeline must connect center of a circle. We need make the “P1” as the port.
When we save the “Auto CAD” document, we must save it in “.dxf” format. Then we can import the “Auto CAD” document of “.dxf” format. Click the “Project Config (C)” -> “import(.dxf)” -> follows:
The layout will appear as it appeared in the previous two methods.
Here we come to the end of explaining how to use LEDEdit 2014 Software? If you have any questions or inquiries, please leave a comment and we will reply to you as soon as possible.
LEDEdit, LEDEdit-K, LEDEdit Effects, LEDEdit animation, Pixel LED Programming, NeonPlay, LEDEasy, Glediator, Jinx!, LEDBuild, Madrix, T1000s, WS2811.